Search:

Type: Posts; User: envisionelec

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    46,307

    Four years have gone by - that was quick. I even...

    Four years have gone by - that was quick. I even had another kid since my last post!

    I had the chance to meet some folks from this-here forum - and was axed about the development of the Analyzer....
  2. Replies
    11
    Views
    7,643

    Yes you did. I will go register now.

    Yes you did. I will go register now.
  3. Replies
    11
    Views
    7,643

    Two and a half years later, an MIA engineer and a...

    Two and a half years later, an MIA engineer and a dream displaced. Well, that was fun.

    I'm looking at doing this again.This time, though, I have friends with deep pockets. My pockets are also a...
  4. Replies
    51
    Views
    15,293

    I was banned from the Parts Express board for...

    I was banned from the Parts Express board for figuring out the manupacturer of their 1kW plate amps.

    After two years, I was reinstated. Three months pass and I was banned again for comparing their...
  5. Helix H1000 Esprit $300 free shipping in the CONUS. Best offers accepted.

    Helix H1000 Mono 600Wx1 at 4 ohms amplifier. Extremely thin profile. I have gone through it completely. I'll never use it. :wacko:

    The box and owner's manual are included, although both are in...
  6. Behringer DCX2496 Ultra-Drive with DSPower Installed $329. Dayton Audio DTA100a $60.

    For sale on eBay now. I have just a few DSPower kits left and decided to blow out a couple BNIB with the DSPower already installed. The units are about a year old...I buy quite a few of these at a...
  7. Behringer DCX2496 Ultra-Drive with DSPower Installed $329.

    I've got a pair of new DCX2496 on eBay for $329 each. That's a $110 (plus shipping) savings over buying the DCX2496 and the DSPower separately.

    Behringer Ultra Drive DCX2496 with Dspower 12V Power...
  8. Replies
    176
    Views
    119,080

    There's a thread over at the SMD forum with...

    There's a thread over at the SMD forum with sensai running his mouth again. I don't care to mess with someone with a violent criminal record, but I'll be sure to contact his parole officer if he...
  9. Replies
    176
    Views
    119,080

    Hehehe. This isn't about Tony (a talented...

    Hehehe.

    This isn't about Tony (a talented engineer) or Steve (a douche canoe). This is about a competing product. A scope isn't used for clip detection because most people don't know what they're...
  10. Replies
    176
    Views
    119,080

    Deleted. Already posted this information.

    Deleted. Already posted this information.
  11. Replies
    176
    Views
    119,080

    Aww, someone deleted the best reply I'd ever...

    Aww, someone deleted the best reply I'd ever read.

    So I had to fire the engineer that was assigned to the project. He's just ridiculously slow and unresponsive. He's only 6 months behind on my...
  12. Replies
    176
    Views
    119,080

    I would, but the engineer working on my other two...

    I would, but the engineer working on my other two projects is far from quick. He's very busy, so I am trying to be patient. TMM has or is in the process of releasing his source code under an Open...
  13. It only happens in forums. But seriously, I truly...

    It only happens in forums. But seriously, I truly enjoy it when people offer suggestions. 99% don't make it, not because I think they're dumb but because they're either impractical or too costly for...
  14. Replies
    176
    Views
    119,080

    TMM, I saw your posts on another forum where you...

    TMM, I saw your posts on another forum where you wondered why the DD1 couldn't detect other types of signal distortion. I want to add that it also fails at symmetry distortion, as well. This is...
  15. Ok, officially started on it today. We're adding...

    Ok, officially started on it today. We're adding A2DP using the latest Bluecore 5 Multimedia Chipset. It is capable of PCM Audio right into the DCX2496 through the AES3 input. I should have a mock up...
  16. Well...interesting. It does seem to be a natural...

    Well...interesting. It does seem to be a natural next step. I will consider it!
  17. Bluetooth Interface for DCX2496...Ideas?

    I'm developing a bluetooth device that will interface with the DCX2496 and will allow you to use it as the master volume control in a fully digital source system. It will also let you make on the fly...
  18. Replies
    176
    Views
    119,080

    Nice! In order to be reliable, some protection...

    Nice! In order to be reliable, some protection needs to be applied to the input to prevent reverse-biasing the OpAmp (will cause latch-up and possible damage). Reducing the input amplitude to its...
  19. Replies
    176
    Views
    119,080

    TMM, you've got a PM.

    TMM, you've got a PM.
  20. Replies
    176
    Views
    119,080

    Instead of the capacitor, can you use a current...

    Instead of the capacitor, can you use a current transformer with a waveshaper?
  21. Replies
    176
    Views
    119,080

    Yeah, that's really slick. Much better than the...

    Yeah, that's really slick. Much better than the single mode of the SMD. I personally just started programming those things. I totally get the concepts, but the syntax gets me every time. I guess I'll...
  22. Replies
    176
    Views
    119,080

    Cool! I did the math on the SMD and found it...

    Cool! I did the math on the SMD and found it slightly more than completely useless for meaningful measurements. If that makes sense to you: you get a gold star.
  23. Replies
    51
    Views
    15,293

    They did the same thing to me even though I'm...

    They did the same thing to me even though I'm selling a low-cost item that nobody else makes. It's not like I'm making a living off a power supply... It was the beginning of the end fer me.
  24. Replies
    51
    Views
    15,293

    Right. I meant I couldn't find a negative...

    Right. I meant I couldn't find a negative reference to Syracuse Customs on their forum. Maybe it's off site?
  25. Replies
    51
    Views
    15,293

    I'm not seeing it...

    I'm not seeing it...
Results 1 to 25 of 137
Page 1 of 6 1 2 3 4